What is roof flashing repair? | Brevard County, Florida | Total Home Exteriors of Florida
“What is roof flashing repair?” our customers ask us this all the time! Our highly trained Brevard County Florida Roof Repairs Experts answer this question over and over again. So we decided to write an blog article about this for Brevard County Florida Homeowners with Roof Issues.
So what is Roof flashing? Simply, it is a material that is placed at points on a roof that are prone to leaks. These are usually areas between various items and the roof, such as skylights, chimneys, or vents, would a few good examples. Further it is also found between different parts of the roof as well. The ‘Flashing’ is usually made of metals that are resistant to corrosion. Flashing serves to direct water away from the leak prone areas towards gutters or off the roof. When roof flashing begins to Deteriorate, it can lead to leaks and damage your house. Unfortunately, some of our competition use lesser quality products like plastic, duct tape, or other composites which causes the leaks to remain in most cases, but the expert roofing contractors of Total Home Exteriors of Florida never use inferior materials.
What Happens When Roof Flashing Fails for Brevard County Florida Homeowners
As stated above, flashing is a material that is used to direct rainwater away from the roof and into gutters or just off of your roof. Roof flashing plays a vital role in maintaining the integrity of your roof. Most all roofs have areas that are prone to leaks. These are generally are areas where water collects, such as valleys on tile roofs or where two roof slopes meet on shingle style roofs. Be aware that places where a roof meets another structure are also prone to leaks at their joints. Because of this, roof flashing is installed almost anywhere a roof joins another structure, such as a chimney, dormer, skylight, or vent. In Florida, it is common to see this based on the fasion design of certain homebuilders.
It is important to be understand that flashing protects your roof from leaks by adding another layer of material specifically designed to redirect water. Without roof flashing, your home will become damaged very quickly during the numerous rainstorms associated with Florida. As your roof begins to deteriorate, this will increase the risk of leaks during major windy rain events including hurricanes and tropical depressions. A roof leak or leaks can have a major effect on homes, causing large amounts of damage well beyond the roof. In the roofing industry, it is known that water generally finds the fastest route to the ground. Thus,if a leak is not noticed and fixed immediately, a home can experience water damage.
Roof Issues from leaks caused by roof flashing damage is common in homes of Brevard County Florida
A leak into your home’s attic can cause moisture to build up and seep into the wooden structure. This could weaken the structure and even cause it to rot and creating possible structural damage. These repairs can be expensive! Many times, Total Home Exteriors of Florida is asked to handle removing and rebuilding parts of your house’s basic framing. We have seen first hand how water damage occurs when water comes in contact with drywall in a ceiling or wall of your home. Unfortunately, the drywall soaks up water and can become waterlogged. Did you know, in Florida that wet drywall creates a number of hazards due to the humidity in the air. Having sub tropical environment with humidity for a majority of the year, the wet drywall can serve as a breeding ground for mold and fungi. We commonly find black mold and fungi in the inner wall and these mold spores become overtime released into your home’s air. This toxic air will make you, your family, and people visiting your house very sick. Unfortunately, removing drywall with black mold and other fungus is a must and it is not always easy.
Some Brevard County Florida homeowners ask us to sub-contract a water damage specialist. They will start by spraying some form of poison on the mold or fungus to kill it. After that, the section of drywall affected by the mold will still need to be removed and replaced. If there is too much moisture in the area, the area may have to be sealed off and treated for days or weeks with a dehumidifier before repairs can be effectively started.
Let’s take a close look at the types of Roof Flashing Repair available
There are many types of flashing, but they all fall into a few broad categories. Materials used for flashing vary. By far the most common material is sheet metal. Roofers usually use galvanized steel for its durability. In some cases aluminum may be preferable. This is often the case with DIY roofing jobs, since aluminum is more easily bent and easier to work with. In some specific situations a roofer may use copper flashing. This is usually done for looks. It is most common on historic homes or homes with unique roofing materials, including roofs made completely of copper.
Another material that can be used for flashing it pvc plastic. This material is cheaper than metal and easier to cut and work with. However, it is not as durable. When exposed to sunlight over a long period, pvc plastic tends to break down. With pvc plastic flashing it may be necessary to monitor the condition of your flashing and repair or replace it as it deteriorates.
Some flashing is now available made of synthetic materials and composites. These materials are relatively new and have different properties. Often they are used for their durability or ease of installation. The professionals at Total Home Exteriors of Florida – Your Roofing Experts can provide helpful information on the latest materials and their benefits.
Where Roof Flashing is Installed?
How flashing is installed depends on where it is installed. The most basic type of flashing is the flashing that collects water in the valleys of your roof. These are the joints where two slopes meet. Flashing in these areas will be installed underneath the shingles on either side. When water reaches the valley it will flow off the shingles and into the gulley created by the flashing. From there the water is safely directed to a gutter, downspout, or simply off the edge of the roof.
- Chimney Flashing – A common location for flashing is around a chimney. Chimney flashing is actually a collection of several types of flashing. Continuous flashing, a single strip of metal (or another material) is installed along the base of the chimney where it meets the roof. Along the sides of the chimney, step flashing is installed. This consists of squares fo flashing that overlap, similar to shingles, and climb up the side of the chimney along with the slope of the roof.
- Saddle Flashing – It is like a little mini roof behind the chimney on the higher side. Also called a cricket, this is a ridged design feature. It directs water and debris to either side of the chimney. That way it does not backup and collect on the high side of the chimney.
- Cap Flashing – This is where the top of the flashing meets the brick (or other material) of the chimney, cap flashing will be mortared or caulked to the chimney. This flashing is attached to the chimney at its top and its lower part overlaps the flashing below. The bottom edge of the cap flashing is molded to direct water outward and away form the step flashing. It keeps water from seeping behind the step flashing.
- Vent Flashing – Flashing is also used around vents in the roof. The type of flashing depends of the type of vent. This flashing is also commonly included with the vent hardware.
- Skylight Flashing – The same is true of skylights. Skylights require flashing around the area where they meet the roof. The flashing is often integrated into the design of the skylight. If it is not, flashing must be installed to prevent leaks around the skylight.
- Dormer Step Flashing – If a house has dormers, flashing will be required where the vertical walls of the dormer meet the sloped roof. Like with a chimney, stepped flashing is installed along the vertical wall of the dormer following the slope of the roof. The step flashing will be capped with cap flashing that is attached to the exterior of the dormer. The base of the dormer will get continuous flashing and the peak of the dormer will get saddle flashing. The area where the roof of the dormer meets the rest of the roof will be treated like other valleys, with standard flashing that rests beneath the shingles on either side.
What is Roof Flashing? | Is this a DIY Project?
Roofing work is never a DIY project. Being on a roof and working on a roof is dangerous! Many people putting up christmas lights get hurt and more with the main danger coming from falls. Without proper equipment, the risk of falling can be even worse. If you are not familiar with working on roofs, it is best to bring in a contractor. Total Home Exteriors of Brevard County Florida is experienced in roof repair and roof replacement. Contact Total Home Exteriors of Florida today to find out how we can help you with your roofing needs.
One common issue with roofing maintenance is the replacement or repair of what is called roof flashing, or simple flashing. Roof flashing is sheet metal installed at any breaks, joints, or edges on your roof to prevent leaks. Most flashing is composed of aluminum or galvanized metal. This means that roof flashing repair can typically be cheap and easy to do, although there are some mistakes to avoid.
If your roof is at the point where you need to repair or replace flashing, stop call us and we can do it for you. Don’t try to get on the roof to repair or replace: step flashing, vent flashing, or chimney flashing. You could break or crack a tile leading to a roof leak. You could be using the wrong tools and materials, thus causing more damage to the intergity of your home’s roof. Here are 3 reasons not to DIY your roof flashing:
- Doing Nothing – There are some things you want to avoid doing when it comes to roof flashing. Even a veteran DIYer does get alittle busy or lazy or maybe forgetful. Waiting to get the roof flashing fixed is not a good idea. If you delay calling us to fix the roof flashing issue – you could be looking at repairing your entire roof with us. Doing the repairs yourself sounds like a great way to save a ton of money, but generally we find that we have to redo most of the work because it was done wrong or not up to Florida Roof Standards. This can cause lots of headaches and not to mention water that leaks into your home is an invitation to many other problems. It can lead to rotted wood, mold, and mildew forming in the walls and ceilings of your home. Before your small leaking roof problem turns into a home nightmare, get it repaired with our Brevard County Florida Roofing Pros.
- Being Careless – Do you own a safety harness? Seriously, do you really think your spouse is a good spotter to catch you in a fall? Are you always be aware of where you’re standing on the roof? Alot of people fall off their roof, so don’t get careless just don’t be hero.
- Weather Issues – We will wait for good weather and put a tarp on your roof to keep the leak from getting worse. Are you keeping up with the weather forecast? We literally heard about a homeowner will didn’t wait for the rainy weather to clear up and fell off the roof of his home. Now he has a repair by roofer and a hospital bill to deal with. We will help repair your roof but we will give it time to dry off before attempting to repair it. We are certified roofers and we understand that your roof might be slippery from the rain. Also, Florida is known for it’s lightning – do you really want to be on your roof and get hit by lightning during a mid-day thunderstorm? Maybe it is best no to take any chances.
- Doing a Sloppy Job – Yes, we have seen people do a rush the job. Why because they are 30 to 45 feet in the air on their roof top. I recently chatted with another roofing contractor that told me how a homeowner just simply used tar and cement to fix cracks on the his roof. But he didn’t understand that the tar needed time to dry and the prep materials as well. This homeowner just tar and cemented a crack without thinking that more work was still needing to be done. Total Home Exteriors of Florida will always supply you a written or verbal quote prior to working on any repair and we will always take our time and do it right.
What are my repair options?
While our competition will offer a variety of buzzwords and fancy types of roof flashing repairs. We know that there are three different types of roof flashing repair.
- Step flashing is when you repair the damage by putting in new flashing over the damaged area. First, snip the new flashing with your shearers, then bend it to a 90-degree angle. Then slide it up the roof, preferably on top of the damaged flashing. Adhere it using your flashing cement.
- Vent Flashing is damage near or on the vents of your roof. First, locate the leak. If the problem is with the pipe itself, you should replace it with a new collar or install a larger collar over the existing pipe. For more severe damage, you may need to install all new vent flashing, which requires removing the shingles and replacing each piece again. Your roofing nails will be used up quickly if this is the case. Make sure you have enough.
- Chimney flashing repairs are done around the chimney area. If the damage and the leak are minor, you should be able to replace the chimney flashing just like you would step flashing. If the mortar joint is deteriorating, the joint will need to be repointed and you may need to have this done professionally. Either way, the damaged area will need to be cleaned with steel wool or the flashing cement will need to be used to finish the job.
Okay, so I think we clearly answered this roof flashing question, but if you have more questions about this topic don’t hestitate to call us. We recommend you call our caring customer service team to get a roof estimate right away. Plus we are a+ rated by the BBB in Central Florida too. Lastly, Total Home Exteriors of Florida proudly serves all of Brevard County in Florida and we love getting referrals. So send us a referal today!